At the end of November last year, I purchased from Gerry the Jag rear axle conversion kit.
The kit was missing "4 shock mounting rods and nuts" and Gerry emailed his supplier to ask him to post them directly to me. Despite several emails to both Gerry and his supplier, these have not been forthcoming (and in the current climate, I don't expect them to be)
So I am looking at sourcing these parts myself...trouble is, I have no idea what they are (apart from the above description) nor what dimensions they are.
Can anyone help? any part completed kit builders that have the parts they could measure for me?
Thank you.
Simon
Gerry's rear axle parts
- simonjrwinter
- Posts: 1367
- Joined: Sun Jan 03, 2010 8:25 pm
- Location: Upminster, Essex.
Gerry's rear axle parts
TR6 (V8) Hawk 289 FIA (V8) Doing my bit for global warming.
Re: Gerry's rear axle parts
Hi Simon, I've only recently fitted mine and they are still accessible.
I'll pull one out and take some pictures and measurements.
I waited ages for my kit but at least it was complete when it arrived.
I'll pull one out and take some pictures and measurements.
I waited ages for my kit but at least it was complete when it arrived.
Kev Davies
DAX Mk4, 383 Chevy Stroker, Tremec. SOLD
Contemporary CCX 3-4028, 445ci Big Block FORD FE,TKO 600. SOLD
Dax De Dion LS2 and T56. SOLD
1965 Ford Mustang 289 Convertible SOLD
In build Hawk 289 (302) Sebring. Awaiting IVA:D
DAX Mk4, 383 Chevy Stroker, Tremec. SOLD
Contemporary CCX 3-4028, 445ci Big Block FORD FE,TKO 600. SOLD
Dax De Dion LS2 and T56. SOLD
1965 Ford Mustang 289 Convertible SOLD
In build Hawk 289 (302) Sebring. Awaiting IVA:D
Re: Gerry's rear axle parts
Are they not stock Jaguar parts? Upper or lower?
Re: Gerry's rear axle parts
This is the lower shock mounting shaft. Call Martin Robey and ask for the nuts and washers to go with it. Or take it to your hardware store and get nuts and washers.
I suspect they will be either 7/16 or 1/2 UNF.
Assuming it is the bottom mount you are after.
https://www.martinrobey.com/jaguar/e-ty ... sion/21100
Hawk may use this Shaft on the top as well ? I am sure you can figure out something. Find out the shock pin diameter and the chassis hole diameter and go from there.
I suspect they will be either 7/16 or 1/2 UNF.
Assuming it is the bottom mount you are after.
https://www.martinrobey.com/jaguar/e-ty ... sion/21100
Hawk may use this Shaft on the top as well ? I am sure you can figure out something. Find out the shock pin diameter and the chassis hole diameter and go from there.
- simonjrwinter
- Posts: 1367
- Joined: Sun Jan 03, 2010 8:25 pm
- Location: Upminster, Essex.
Re: Gerry's rear axle parts
Thank you gents, much appreciated
Simon
Simon
TR6 (V8) Hawk 289 FIA (V8) Doing my bit for global warming.
- simonjrwinter
- Posts: 1367
- Joined: Sun Jan 03, 2010 8:25 pm
- Location: Upminster, Essex.
Re: Gerry's rear axle parts
Just measured. The tubes in the wishbones are 120mm long but the tubes in the diff support are 135mm
TR6 (V8) Hawk 289 FIA (V8) Doing my bit for global warming.
- simonjrwinter
- Posts: 1367
- Joined: Sun Jan 03, 2010 8:25 pm
- Location: Upminster, Essex.
Re: Gerry's rear axle parts
Thanks for the advice gents, Gerry was kind enough to sort it for me, parts are on their way.
Simon
Simon
TR6 (V8) Hawk 289 FIA (V8) Doing my bit for global warming.
- StewbieC
- T289R Committee
- Posts: 1360
- Joined: Mon Oct 13, 2008 12:50 pm
- Location: out in the sticks, Shropshire
Re: Gerry's rear axle parts
Might be M14CobStang wrote: ↑Mon Mar 23, 2020 10:37 am This is the lower shock mounting shaft. Call Martin Robey and ask for the nuts and washers to go with it. Or take it to your hardware store and get nuts and washers.
I suspect they will be either 7/16 or 1/2 UNF.
Assuming it is the bottom mount you are after.
https://www.martinrobey.com/jaguar/e-ty ... sion/21100
Hawk may use this Shaft on the top as well ? I am sure you can figure out something. Find out the shock pin diameter and the chassis hole diameter and go from there.
________________________________________________
Stu
Hawk 289, 66 Mustang Fastback with a 289 maximum smiles per mile..
Stu
Hawk 289, 66 Mustang Fastback with a 289 maximum smiles per mile..
Re: Gerry's rear axle parts
Hi Simon, Glad you got it sorted with Gerry. I’ve built up my jag IRS and it’s sitting in the garage ready to be fitted.
Bit of head scratching going on as not quite sure how I am going to lift up into position yet, might hire a motorbike lift to Jack it up under the car. Be interested how you get on.
Bit of head scratching going on as not quite sure how I am going to lift up into position yet, might hire a motorbike lift to Jack it up under the car. Be interested how you get on.
You do not have the required permissions to view the files attached to this post.
- simonjrwinter
- Posts: 1367
- Joined: Sun Jan 03, 2010 8:25 pm
- Location: Upminster, Essex.
Re: Gerry's rear axle parts
That’s interesting as that’s exactly what I plan to use to install mine. I used to own a m/cycle lift, but gave it to a pal. Going to have to borrow it back!
Simon
Simon
TR6 (V8) Hawk 289 FIA (V8) Doing my bit for global warming.